![\"Image20241101143052\"](\"https:\/\/content.kegworks.com\/hs-fs\/hubfs\/Blog\/Image20241101143052.jpg?width=800&height=533&name=Image20241101143052.jpg\")
<\/p>\n
Adding bar rail molding<\/a>, also known as Chicago bar rail or wooden bar armrests, lends a polished, professional finish to any DIY home or commercial bar project. Primarily, it provides a comfortable perimeter for guests, whether seated or standing, and creates a protective lip to contain glassware and spills on the bar top, keeping the floor clean and safe.<\/p>\n <\/p>\n Our wooden bar rail molding<\/a> is\u00a0available in four types of wood: cherry, hard maple, red oak, and poplar. Each option offers a different color, density, and grain pattern.<\/p>\n All of our wooden arm rests come unstained so that you can match the arm rest to your bar or choose a complementary stain or color if you are looking to create contrast. Be sure to stain, varnish, or paint your arm rail and let each piece dry fully before installation.<\/p>\n If your bar is 12 feet long, don\u2019t just buy 12 feet of molding. Buy some excess length to give yourself room for cuts and errors.<\/p>\n Triple-check your numbers before you start cutting. Trust us on this one.<\/p>\n You received your arm rest order and are ready to install. Here\u2019s how you go about it.<\/p>\n Our wooden arm rails rest at an angle over two pieces of stepped wood. The top piece of wood is your finished bar top; the bottom piece of wood juts out further and provides structural support. Our wooden arm rails come in 2′, 4′, and 8′ lengths. We recommend buying the next largest rail length for each straight run of your bar and cutting it down to size. This will reduce the number of seams in your finished product. If you have a run longer than 8′, you must seam two pieces of rail together.<\/p>\n We recommend using a scarf joint if you are seaming together two lengths of arm rest in a straight run. This requires cutting a beveled edge so that the two pieces fit together at an angle, making for a tighter seam.<\/p>\n If your bar has a corner or corners, and you decided to go the miter joint route, cut the ends of your adjoining molding at a 45-degree angle. Note that arm rest has a wide profile, so cutting it to a precise 45-degree angle is difficult. If you are new to woodworking, you may want to seek the help of someone more experienced. You might also find this video<\/a> on cutting precise miter joints helpful.<\/p>\n If your bar has a corner or corners and you opted for radius corners, you could cut a beveled edge to form your seam. However, cutting a radius corner on a miter saw can be particularly difficult. Instead, we recommend a simple butt joint. You may choose to cut clean ends, but no special cuts are necessary.<\/p>\n You want to be sure everything fits together as intended before you start drilling and gluing. Don\u2019t skip this step.<\/p>\n Wooden arm rests are fastened in regular intervals from the underside (see above figure for screw placement). To secure the molding, pre-drill holes in the underside, taking care not to drill through the wood. Use clamps to hold the molding in place.<\/p>\n Once your holes are drilled, you can begin attaching your molding. With glue on the seam where the arm rail meets the bar top, align and screw the molding into place. Wipe away excess glue for a clean finish. If your arm rail does not end at a wall, attach bar rail molding end caps<\/a> for a finished look. These should be glued on to avoid visible nails.<\/p>\n Once installed, your bar will boast a professional, finished appearance with added comfort for your guests. Enjoy the results!<\/p>\n<\/div>\nChoosing the wood for bar arm rests<\/h2>\n
![\"Bar](\"https:\/\/content.kegworks.com\/hs-fs\/hubfs\/Imported_Blog_Media\/Arm-Rest-Finishes-1-2.jpg?width=800&height=198&name=Arm-Rest-Finishes-1-2.jpg\")
<\/p>\n\n
Choosing between mitered and rounded corners<\/h2>\n
![\"bar](\"https:\/\/content.kegworks.com\/hs-fs\/hubfs\/Imported_Blog_Media\/arm-rest-corners-2.jpg?width=800&height=300&name=arm-rest-corners-2.jpg\")
<\/span>When planning any armrest project, consider how to address the bar’s corners:<\/p>\n\n
<\/span><\/li>\n<\/ul>\nInstallation tips for bar rail molding<\/h2>\n
1. Give yourself enough length<\/h3>\n
2. Measure, measure, and then measure again<\/h3>\n
How-to install wooden bar rail molding<\/h2>\n
Tools needed<\/h3>\n
\n
1. Prepare the bar top<\/h3>\n
<\/span><\/p>\n![\"bar](\"https:\/\/content.kegworks.com\/hs-fs\/hubfs\/Imported_Blog_Media\/arm-rest-install-4.jpg?width=800&height=304&name=arm-rest-install-4.jpg\")
<\/span>As you can see in the figure above, the bottom piece of wood should measure \u00be” thick and extend three inches past your finished bar top. Your finished bar top should measure 1 \u00bc” thick. If your bar top is thinner, shim it with a piece of unfinished scrap wood (you won\u2019t see the shim when the installation is complete). Use glue and pneumatic staples to adjoin the structural wood, finished bar top, and any shim you might use.<\/p>\n2. Cut molding to length<\/h3>\n
3. Dry fit all pieces<\/h3>\n
4. Pre-drill holes<\/h3>\n
![\"bar](\"https:\/\/content.kegworks.com\/hs-fs\/hubfs\/Imported_Blog_Media\/arm-rest-install-2-2.jpg?width=800&height=497&name=arm-rest-install-2-2.jpg\")
<\/p>\n5. Assemble and finish arm rest<\/h3>\n